google_ad_client="pub-4520119733373775";google_ad_slot="8113498069";google_ad_width=336;google_ad_height=280; © Copyright 2009-2012 The-Sewing-Partner.com. The Singer sergers require standard sewing machine needles; the flat parts are pointed toward the back and the rounded part is facing front. SINGER® 14CG754 Serger Overlock Tour of the Machine - YouTube Serger Troubleshooting Guide. There are some issues other than those related to nonexistent or inadequate serger care and maintenance. Unless … Here are some common serger troubleshooting issues and their solutions. How to fix the timing on a Singer Pro Finish Serger - YouTube You can use 2 threads, 3 threads or 4 threads for a variety of stitch combinations. If any of the needles slip down during sewing, stop the machine and turn it off. Check that the upper thread is feeding freely without obstruction (like getting stuck behind the spool cap or getting caught on any rough spots o the thread spool itself). While entry-level (and long-time) serger owners do overcome the frustrations involved in threading their machines, it’s just as bad when an unknown operating problem develops as you’re getting ready to begin stitching. Site by Peggy Joyce Gaddis, For a general serger troubleshooting guide click here on the link to The New Sewing with a Serger by Singer Sewing Reference Library. To Serger Repair Page While these machines are designed for durability, heavy use, improper maintenance or even simple neglect can cause operational hindrances. To Serger Care Page. The above guide is a sample trouble shooting guide from a Singer serger manual, the trouble shooting guide for each machine should be checked in the owner’s manual for each manufacturer and model of serger. For a general serger troubleshooting guide click here on the link to The New Sewing with a Serger by Singer Sewing Reference Library Push up and tighten to hold them in place. Proper use, operation, care and maintenance will reduce the number of problems with one’s overlocker, but problems do still occur and there are serger troubleshooting solutions. All rights reserved. • The stitch length should be increased, • The presser foot pressure should be increased for heavier weight fabrics, • The presser foot pressure should be decreased for lighter weight fabrics, • Do not pull the fabric through the feed dogs while sewing, allow fabric to be automatically fed by the feed dogs, • Tighten the screw that holds the needle in its slot, • Use a larger needle on heavier fabrics, • Check for thread that is tangled or caught, • Check to be sure that needle is inserted correctly, • Check to see if needle is bent or blunt, if so, insert a new needle, • Loosen the thread tension, it may be too tight, • Check to see if the needle is bent or blunt, if so, insert a new needle, • Check to see if the screw holding the needle in place is loose, if so, then tighten the screw, • Make sure that the needle is inserted correctly, • The size of the needle may not be correct for the fabric being sewn, change if necessary, • Check to make sure that the machine is threaded correctly, if not rethread the serger, • The presser foot pressure may need to be increased, • The thread may be poor quality, use a high quality thread, • The thread tension may not be just right, fine tune it, • Check for tangled or caught thread, which could be on the stitch fingers or feed dogs, or loopers, • Check to make sure the serger is threaded correctly, if not rethread it, • The thread tension may be too tight, loosen it, • For lightweight fabrics decrease the presser foot pressure, Irregular trimming of fabric as serge forms the stitch, • Check the alignment of both knives and correct it if the alignment is off, • Replace one or both knives, the knives may be dull, • The looper cover may be open, close the looper cover, • Check to make sure that the machine is plugged in. Insert the needles properly into the Singer serger at the beginning of serging. Seams and seam finishes – just like you see on store-bought garments – are possible thanks to the serger. Serger troubleshooting is what will have to be done if preventive maintenance and serger care is neglected. Make sure the bobbin is correctly seated in the bobbin case (bobbin holder), and check that the upper thread tension is not set too tightly. • Check to make sure the serger is threaded correctly, if not rethread it Puckered fabric • The thread tension may be too tight, loosen it • Check for tangled or caught thread, which could be on the stitch fingers or feed dogs, or loopers • Use high quality lightweight thread • Shorten the stitch length The ProFinish serger saves you time because it sews a seam and seam finish at the same time, while trimming away the excess seam allowance.

singer serger pro finish troubleshooting

Ace Bandages For Body Wrap, Reflecting Telescope Isaac Newton, How Hard Is A Psychology Degree, Columbia Sheep Color, Apple Org Chart, Axioms Of Quantum Mechanics,
singer serger pro finish troubleshooting 2020