0000007139 00000 n
0000289557 00000 n
0000004255 00000 n
If Base B works, it means the 2 beds will work together with one remote. This question is related to Nautilus. 0000004220 00000 n
0000035346 00000 n
0000004300 00000 n
0000260226 00000 n
0000301868 00000 n
1. 0000005818 00000 n
remote control 1. To program, adjust the base to the desired position, then press and hold the flashlight button until the remote backlight flashes once and then press the MEM button within 2 seconds to record the position in the memory. Using the same remote, Press + Hold the red button on the control box (on Base B) for 3 seconds. When it shows the red indicating light, press any button on the remote. 2. Browse the Consumer Discussion Forum. 0000268334 00000 n
Raise the head and foot to the desired position, hold the TV/PC button in for 3-4 seconds, once the display on the remote shows an all flat image, you can release the button. This will allow the remote to pair with the base. 0000257597 00000 n
Release the down buttons on the learn switch and the foot up button on remote control 2. When it shows the red indicating light, press any button on the remote. 0000004390 00000 n
0000005705 00000 n
0000000016 00000 n
0000305485 00000 n
2. Mattress Owner's Manual. If the massage works, then there is no problem with the massage. 0000309022 00000 n
When it shows the red indicating light, press any button on the remote. The Zero Gravity Preset position is pre-programmed. 3. 0000009642 00000 n
1. 0000006708 00000 n
0000001556 00000 n
0000263520 00000 n
Customers must purchase two 9 volt batteries and install them in the AC/DC adapter on the Power Unit. level 2 0000009240 00000 n
0000007647 00000 n
19 63
0000009985 00000 n
asked Dec 13 '17. Soft or very firm mattresses won’t provide you with the necessary support. Press + Hold the red button on the control box for 3 seconds from Base A. If Base A works then move to the next step. 0000004345 00000 n
Using the same remote, Press + Hold the red button on the control box (on Base B) for 3 seconds. 0000006217 00000 n
0000340859 00000 n
0000003261 00000 n
0000321887 00000 n
0000301948 00000 n
0000019635 00000 n
Ask the Experts a Question. 0000005337 00000 n
While continuing to hold the down button on the learn switch for base 1, press and hold the foot up button on remote control 2 for 3 seconds. Browse the Expert Q&A. 0000318350 00000 n
Press + Hold the red button on the control box for 3 seconds from Base A. 0000294482 00000 n
0000262875 00000 n
0000278218 00000 n
xref
Side sleepers require the softest mattresses. If it works, then the two bases are un-synced. how to set the memory on the remote. 0000003803 00000 n
81 0 obj
<>stream
%%EOF
Step 4 Repeat Step 3 for base 2. 0000002137 00000 n
Press + Hold the red button on the control box ��uǐ;
8��7i v �H214`������!��aC �+�����͆1�A�ACŁ$�'�v�L_%r�x��?P���i��c
��G'. Mattress Glossary. 0000334558 00000 n
0000002809 00000 n
0000076006 00000 n
0000266819 00000 n
0000004913 00000 n
0000004616 00000 n
0000004435 00000 n
After the position has been saved, press the memory button to return the base to this position from any other position. 0000267521 00000 n
This is important. Your Mattress. 0000010390 00000 n
0
0000273586 00000 n
Raise the head and foot to the desired position, hold the Lounge button in for 3-4 seconds, once the display on the remote shows an all flat image, you can release the button. Ask the Community a New Question. To sync the remote with the base, hold the red button on the control box in for 5 seconds, at the same time, hit a button on the remote to turn it on. trailer
After installing the two 9 volt batteries, press the flat button to get the bed flat. Press + hold "TIMER/ALL OFF'' buttons until the small lock shows unlock. Related Purchases. 2.
h�b``�```;�������A���bl,��00�>�@��.�ؼ��z��-ݞ��'(^^ށ Step 5 Press either the head or foot button on each remote 0000004591 00000 n
0000276310 00000 n
0000337011 00000 n
0000002677 00000 n
startxref
0000314307 00000 n
0000063097 00000 n
0000331942 00000 n
0000270432 00000 n
0000294413 00000 n
1. 19 0 obj
<>
endobj
If Base A works then move to the next step. 0000332105 00000 n
%PDF-1.7
%����
0000274402 00000 n
0000259962 00000 n
This will function as a battery backup, which will drop the base to the flat position in case the power goes out. 0000004480 00000 n
0 31 how to set the memory on the controler. 0000001965 00000 n
You can sleep on your sides and experience serious pressure relief in the mattress range of 3 to 6. <]/Prev 525684>>
Meanwhile, press head massage button on the remote Side Sleeper. 0000290370 00000 n
The TV/PC preset is now programmed. 0000311042 00000 n
If you have 2 Twin XL bases synced together working off 1 remote, and you want to un-sync them so you can work each base independently, follow these instructions: Press and hold the red button on control box A for 5 seconds, then press any button on remote A. The Lounge preset is now programmed.