When she is not at work, Taylor enjoys watercolor painting, hiking, and spending time with her fiancé, family, and friends. Who is BTOD.com and The Breakroom Blog? When it detects an object in the way, the table will stop moving upwards and then slightly move down, giving you room to remove whatever is in the way. To learn more about the products we sell, our review process and why you can trust us, please visit: Why we’re different. Often times, the table will turn back on once it’s had a break. Press and hold the down arrow button (▼) until the table reaches its lowest position. There may be times where you think your control box or motor(s) are broken, when really your desk just needs to be reset. If the motors don’t have a good self-locking mechanism, the motor and spindle can turn when it’s supposed to maintain its height position. If you’ve given the table adequate rest time and it still won’t go down, complete a manual reset. The Duty cycle tells us the maximum amount of time the control box can be active (moving the desk up or down) and how long it needs to be inactive (in its rest stage). However, this list does share the most common causes and solutions and is a great place to start when you first notice that your desk won’t move. Leave a comment. Sentinel 2-Leg Sit Stand Desk Instructions 38″-40” Wide; Sentinel 2-Leg Sit Stand Desk Instructions 54″-72″ Wide; Sentinel 2-Leg Sit Stand Desk Instructions 78″-90″ Wide; Sentinel 3-Leg Sit Stand Desk Instructions 54″-72″ & 78″-90″ Wide; Sentinel 3-Leg Sit Stand Desk Instructions 5472-3648 & 7890-3648 While one motor may turn, the second will either remain still or turn more/less than the first motor. Many standing desks have a collision detection feature that prevents the desk from hitting another object and causing any harm or damage. You can then go on using it as you normally would. Check all other cords for the desk’s motor or control box and make sure they’re secure. You can send an email to us with any questions, and you will get our reply within 24 hours. For standing desks, your reference point is going to be your desk’s lowest position. Even after you complete the rest, you should still allow the desk to rest. FEZIBO standing desk is a height adjustable desk that helps promote better posture, reduce back and neck pain, promote blood circulation, and reduce the risk of other diseases. cannot exceed 325 lbs. The table may not be assembled correctly or there may be other manufacturing defects. A lower container stop is a setting a user creates to reprogram the desk’s minimum height. This typically happens for one of two reasons: the desk was temporarily unplugged and plugged back in OR the outlet lost power. For safety reasons, be sure to remove anything that is below your desk, especially if you had any container stop settings. If your desk is trying to support too much weight, an overload can occur. Taylor Kiley
An upper container stop is a setting a user creates to reprogram the desk’s maximum height. For many desks, every time the power is lost, the table will go into reset mode. You will need to either change or delete the lower container stop to make the table go up past the current setting. Once your desk reaches the lowest position, your desk will be reset and should be back to normal. In this blog, I’m going to share the most common reasons a standing desk won’t go up or down and how to fix it. Often times, the table will turn back on once it’s had a break. If you have a standing desk, it is almost guaranteed that you will have to reset it at some point. But why? So, instead of being able to go to 48”, you can set the max. The desk is saying “this is too much work for me to lift” and to protect its components, it shuts off. To fix this, just remove some of the weight off your desk. See the images below to see how to better identify if a cable is securely inserted. FEZIBO Email: hello@fezibo.com
When your desk loses power, it also loses its memory. A manual reset can override the cycle time resting period that’s currently turned on. So, instead of being able to go all the way down to 24”, you can set the minimum height to 28”. Once the desks become uneven, one of two things can happen. The desk is saying “this is too much work for me to go higher,” and to protect its components, it shuts off. Remove anything from under the desk that may obstruct travel. 2. You may have something that’s mounted above the desk that’s stopping it from traveling upwards. Your email address will not be published. Then, release. 12 Reasons to Avoid Standing Desks Under $400. Your desk may turn on before 18 minutes has gone by. Pricing on the Learning Center is for reference only. If at any point your desk lost power, or became unplugged, your desk will only move down. To help prevent this problem, use a wire management solution to keep wires out of the way. There are many different reasons why your standing desk is getting stuck, and it can be challenging to find the correct way to fix it. My Standing Desk Only Goes Down: How-To Reset Your Desk Taylor Kiley 02 Dec 2019 Buying Tips and Guides Leave a comment If you have a standing desk, it is almost guaranteed that you will have to reset it at some point. Once you’ve done that, go ahead and reset the desk. (*Note: Your desk will move slowly as part of a safety precaution. Please call our sales department for the most accurate pricing. You should notice that the desk dips down and slightly rises, and then stops (indicating a successful reset). Then plug your desk back in. In many cases, when a standing desk loses and then regains power, it automatically goes into reset mode. Your desk should automatically turn back on and begin functioning as normal. Read honest and unbiased product reviews from our users. height to 40”. You should hear a few clicks. 2.) Before you reset your sit stand desk, check all cables to make sure they’re securely connected. Your table may move up just slightly, signaling your desk has been reset. How Much Does An Electric Standing Desk Cost? Every height adjustable table has a maximum lifting capacity. When it detects an object in the way, the table will stop moving downwards and then slightly move up, giving you room to remove whatever is in the way. The desk must do a complete reset in order for the leg to be realigned and even. If you’ve tried that and it doesn’t work, complete a manual reset. Common objects include chairs, mobile pedestals, file cabinet, etc. If the control box reaches the maximum amount of active time, it will turn on a mandatory rest period to prevent overheating. While being in reset mode, a sit stand desk can only travel downwards. Every height adjustable table has a maximum lifting capacity. Plug the power cord into the wall socket. Unfortunately, there may be a problem with the desk’s internal components. Tackling these common causes first on your own can either completely solve the problem, or help save you time on the phone with tech support if it happens to be a malfunctioning issue. If you were to call your desk’s manufacturer, technical support likely go through this same troubleshooting list that we went through in this article. Hold the DOWN button again for approximately 10 seconds and then release (Note: if you have an Advanced Keypad it will display "ASR"; the Basic 2-Button Keypad does not have a display; the Advanced Paddle Keypad will display "RESET"). Check for any items above your desk that may be getting in the way, and remove them. Unplug the desk from the power outlet and wait 30 seconds. This is something that’s referred to as the Duty Cycle. 02 Dec 2019
They’re used to prevent collisions between your sit stand desk and another object, like a chair or mobile pedestal. How to fix this UPDESK: How to Fix Common Error Codes for Your Standing Desk